Cog 18 pin 12864 LCD
Kenyelletso ea Sehlahisoa
| Nomoro ea Mohlala | RXMG-12864Q |
| Boholo ba Pontšo | 41.8x26.1mm(VA) |
| Mofuta | STN |
| Molaoli | ST7565 kapa ho lekana |
| Ts'ebetso ea hona joale | <700uA(3.3V) |
| Sehokedi | Seriale |
| Voltage e sebetsang | 3.1~3,5V |
| Sheba tataiso | 6H |
| Backlight | Bosoeu |
| Mokhoa oa ho bonts'a | Stn negative blue |
| Mocheso oa ho sebetsa | -10 ~ 60 ℃ |
| mocheso oa polokelo | -20 ~ 70 ℃ |
| Sesebelisoa | Sebopeho, ponts'o ea linomoro bakeng sa printa, lisebelisoa, joalo-joalo |
Skrine se seng sa 12864 LCD seo u ka se buang:
Mosebetsi oa Pin:
| Pina NO. | Pin Lebitso | Tlhaloso ea Pin |
| 1 | CS1 | Khetho ea chip |
| 2 | /CS | |
| 3 | /RST | Seta lets'oao bocha |
| 4 | SO | |
| 5 | A0 | Kgetho ya data/taelo(H/L) |
| 6 | SI | |
| 7 | SCK | Ho kenya oache ea serial |
| 8 | SCLK | |
| 9 | CDA | Kenyelletso ea data ea serial |
| 10 | NC | |
| 11 | VDD | Phepelo e ntle ea matla |
| 12 | LED + | Positive backlight power supply |
| 13 | VSS | Phepelo e mpe ea motlakase, fatše |
| 14 | LED- | Phepelo ea matla a backlight a fosahetseng |
| 15 | LED- | Phepelo ea matla a backlight a fosahetseng |
| 16 | NC | Ha ho |
| 17 | LED + | Positive backlight power supply |
| 18 | NC | Ha ho |
Litšebeletso tsa Rōna
Customization :
| Pontšo | segement, graphic, character monochrome lcd module&TFT amoheloe |
| Mokhoa oa ho bonts'a | TN,STN,FSTN,HTN,transflective,reflective,transmissive, yellow green,blue,gray boikhethelo |
| Mofuta oa ponts'o | COB,COG,TAB |
| Lcd botenya(cm) | 0.11,0.14 |
| botenya ba backlight(cm) | 2.8,3.0,3.3 |
| Sehokedi | Parallel(8bit,4bit,16 bit,80mode,68mode),serial(i2c,spi,uart,usb) |
| Molaoli | Taba ea boikhethelo |
| IC | E-shoa kapa e pakiloeng ka boikhethelo |
| Hardware kapa software | Bohle ba amohetse |
| Boitsebiso bo fanoeng | All idear, sampole, photo, ho taka, sebelisa bukana joalo-joalo li lokile |
1, ke batlaMojule oa LCD o bonts'a linomoro tse 8 mme boholo ba kemiso ke 35mm * 70mm………?
Karabo: Ha ho bothata. Taba ea pele, pls re romelle pampiri ea hau ea ho taka kapa lisampole; re tla hlahisa e loketseng haeba e le lihlahisoa tse tloaelehileng. Kapa re ka fetola ho latela e 'ngoe ea eona.
2,Mojule ona oa LCD ke seo re se batlang, empa se seholo, na u na le saese e nyane?A'me litaba tsa ponts'o li hloka ho fetoloa hanyane.
Karabo: Bakeng sa karolo ea mofuta oa LCD module, haeba u hloka ho fetola boholo ba kemiso kapa lihlahisoa tsa pontšo, LCD glass.mold e ncha e hlokahala. Re tla u tsebisa ka hlobo
tefiso ka mor'a ho tiisa ha u lefa,re tla qala pampiri ea ho taka bakeng sa ho e hlahloba.
3, leseli lena la morao-rao la LCD le botala bo mosehla,empa Ibatla blue backlight.
Karabo: ha ho bothata, re ka u fetola.
4, ke batla ho etsa mojule o mocha oa LCD.Cu etsa'ng?
Karabo: E, re ka khona. Ka kopo, romella pampiri ea hau ea ho taka. Haeba ha u so ka u mpolella boholo ba kemiso ea ponts'o ea LCD, tlhaiso-leseling, haeba ho hlokahala lebone la morao kapa PCB.
boto le IC, Re tla hlahloba litšenyehelomme ke o fe theko haufinyane.
5, Ke eng e etellang pele nako ea ho sebetsa
Karabo: matsatsi a 15 ho isa ho a 30 ka mor'a ho taka pampiri ea netefatso le tefo ea tefo ea lisebelisoa, re ka u bolella nako e nepahetseng ha u tiisa pampiri ea ho taka
6,O ka re romella lisampole hore re li hlahlobe?
Karabo: E,. Odara ea lisampole e teng
7,Ke eng eNako ea ho Eta Pele?
Karabo: Haeba re na le stock bakeng sa tse tloaelehileng, nako e etellang pele ke letsatsi le le leng ka mor'a tefo. Haeba ke tlhahiso ea bongata bakeng sa tse khethehileng, nako e etellang pele ke matsatsi a ka bang 1530.
Haeba re ka qeta pejana, re tla romelalintlha tsa hau esale pele
8 , Ke mekhoa efe ea ho lefa eo u ka e amohelang?
Karabo: Hajoale re amohela T/T feela.
